Hp 5500 Switch Firmware Download

Latest firmware for Comware Switch(product model-JG240A) Hi Can anyone tel me what is the latest firmware for HP 5500-48G-PoE+EI Switch w/2 intf slts. I Could able to find the latest firmware for this switch. But i am bit confused about the firmware. NOTE: Firmware files for the switches are included in the Moonshot Component Pack zip file but are not located inside the nested firmware file zip (cp.zip).This allows you use HP SUM to update all Moonshot System firmware except for switch firmware files. Switch firmware updates must be done from either the Moonshot iLO CM firmware CLI or from the switch CLI. Review information on all NETWORKING: Networking Switches by Hewlett Packard Enterprise, compare and find the right product for your business. Review information on all NETWORKING: Networking Switches by Hewlett Packard Enterprise, compare and find the right product for your business. 24-port fully managed Fast Ethernet PoE+ switch with.

Update switch firmware from either the Moonshot iLO CM firmware CLI, or from the switch CLI.

NOTE: Firmware files for the switches are included in the Moonshot Component Pack zip file but are not located inside the nested firmware file zip (cp<XXXXXX>.zip). This allows you use HP SUM to update all Moonshot System firmware except for switch firmware files. Switch firmware updates must be done from either the Moonshot iLO CM firmware CLI or from the switch CLI.

IMPORTANT: Moonshot iLO CM firmware CLI updates are compatible with the following switches:

  • Moonshot-45G Switch Module

  • Moonshot-180G Switch Module

To update the firmware for an Moonshot-45XGc Switch Module, you must access the switch CLI. See Updating HPE Moonshot-45XGc Switch Module firmware.

​

  1. Access the Moonshot iLO CM firmware CLI. For more information, see Connecting CLI sessions.

  2. Enable TFTP transfers by entering the enable tftpenable tftp command.

    For example:

  3. (Optional) If needed, copy the firmware file to the Moonshot iLO CM firmware flash repository by entering the add firmware fileadd firmware file command.

    For example:

  4. Update the switch firmware by entering the update firmwareupdate firmware command.

    For example:

    NOTE: The uploaded filename used in the add firmware file command may not be the same as the filename used in the subsequent update firmware command. Enter the show firmware files command to display the name you must use with the update firmware command.

  5. Power off and then power on the switch by entering set switch power commands.

    For example:

  6. Following standard security precautions, disable TFTP access by entering the disable tftp command.

​

To access the switch CLI interface:

  1. Connect one end of a serial cable to the serial port on the Moonshot Uplink Module and the other end to a laptop or other local machine.

  2. On the local machine, start PuTTY. Choose Serial as the connection type, and configure the settings (115200/8-N-1):

    ​

    PuTTY Configuration

  3. Click to start the switch CLI session.

​

Updating HPE Moonshot-45G and 180G Switch Module firmware

Copy the switch firmware file using TFTP, SFTP, or SCP. This example uses TFTP.

Before you begin:

​

  • Verify that the current switch module firmware is earlier than the version included in this Moonshot Component Pack using the show bootvar command. Your component may already have the latest firmware installed.

  • Verify communication with the TFTP server with an RCMP ping.

​

Hp 5500 Switch Firmware Upgrade

  1. Copy the firmware image from the TFTP server to the alternate firmware bank of the switch:

    copy tftp://<ip_address>/<path>/<filename> alternate

    For example:

  2. Configure the switch to boot from the alternate image:

  3. Verify the switch boot information:

    The output for this command displays the primary, alternate, current-active, and next-active firmware file versions.

  4. Reset the switch and boot from the new image:

  5. After the switch finishes rebooting, verify that the firmware update was successful:

    The output for this command shows that the switch boots the image from the alternate flash file system, but the image loads and runs in the primary flash file system.

  6. Make a backup of the image:

    NOTE: This removes the ability to downgrade the firmware to the previously installed version. Confirm that you are satisfied with the firmware before running this command.

​

Updating HPE Moonshot-45XGc Switch Module firmware

Copy the switch firmware file using TFTP, SFTP, or SCP. This example uses TFTP.

Before you begin:

​

  • Verify that the current switch module firmware is earlier than the version included in this Moonshot Component Pack using the display version command. Your component may already have the latest firmware installed.

  • Verify communication with the TFTP server with an RCMP ping.

Hp 5500 Switch Commands

​

Extreme Switch Firmware Download

  1. Copy the Moonshot-45XGc Switch Module firmware file to a local TFTP, SFTP, or SCP share.

  2. Load the Moonshot-45XGc Switch Module firmware file into the switch from TFTP, FTP, or SCP.

    ​

    Command example (FTP):

    ​

  3. Load the firmware by entering the boot–loader command.

    Drivers including: imageRUNNER 1310, imageRUNNER 1630, imageRUNNER 1670F, imageRUNNER 1330, imageRUNNER 1370F, etc. This page contains full list of Canon imageRUNNER 1310 1330 1370F 1630 1670F Drivers available for free download. The drivers in this category is updated weekly, so you can always download the latest Canon drivers here! Drivers canon ir 1310 para windows 7.

    <HP> boot-loader file flash:/<Moonshot-45XGc Switch Module firmware> slot 1 main

  4. Reboot the switch by entering the reboot command.

    <HP> reboot